[RS3Dell]

Been spending the last few nights taking off the Bilstein B14s to fit the Ohlins DFV which I would have fitted if they were available at the time I bought the B14s.

Top shelf suspension kit comes preadjusted stock ride height at the rear & 10mm drop at the front with 20 click damping adjustment.

 IMG_20200623_205527.jpg   42.17K   23 downloads  IMG_20200623_220842.jpg   45.61K   24 downloads  IMG_20200622_211158.jpg   43.91K   20 downloads

[T-800]

Been spending the last few nights taking off the Bilstein B14s to fit the Ohlins DFV which I would have fitted if they were available at the time I bought the B14s.

Top shelf suspension kit comes preadjusted stock ride height at the rear & 10mm drop at the front with 20 click damping adjustment.

IMG_20200623_205527.jpg IMG_20200623_220842.jpg IMG_20200622_211158.jpg

Good work Dell.

Shame you didn’t stand upright for the photos


Sent from my iPhone using Tapatalk

[jimojameso]

Look great mate! Very envious

[RS3Dell]

Good work Dell. Shame you didn’t stand upright for the photos Sent from my iPhone using Tapatalk

Great spotting from you Sean Like some on here the photos post@ 90' for some unknown reason
May be a encoding issue with my phone/RS3OC site.

Dell.

[RS3Dell]

Good work Dell. Shame you didn’t stand upright for the photos Sent from my iPhone using Tapatalk

Great spotting from you Sean 😂 Like some on here the photos post@ 90' for some unknown reason 🙄
May be a encoding issue with my phone/RS3OC site.

Dell.

[T-800]

Great spotting from you Sean Like some on here the photos post@ 90' for some unknown reason
May be a encoding issue with my phone/RS3OC site.

Dell.

And double posts

Bloody internet malarky.


Sent from my iPhone using Tapatalk

[RS3Dell]

And double posts Bloody internet malarky. Sent from my iPhone using Tapatalk

Another fine spot Sean

Dell.

[T-800]

Another fine spot Sean

Dell.

Tis the sunny weather mate.


Sent from my iPhone using Tapatalk

[RS3Dell]

Tis the sunny weather mate. Sent from my iPhone using Tapatalk

😂

Dell.

[MarkMac-RS3]

Great spotting from you Sean 😂 Like some on here the photos post@ 90' for some unknown reason 🙄
May be a encoding issue with my phone/RS3OC site.

Dell.

I have the same issues at times. I have to rotate the photo 90 degrees on my phone, save it, then rotate it back to normal and save it, seems to cure the issue.

[GreyDave]

Very nice Del. What you doing with the B14s? 👀

[RS3Dell]

Very nice Del. What you doing with the B14s?

Dave.

I need to give then a very good clean up 🙄 Undecided at this time mate 🤔

Dell.

Edited by RS3Dell, 27 June 2020 - 02:00 PM.

[Pil5burydoughboy]

If you wanted ohlins & they weren't available why opt for B14's & not B16's?

[RS3Dell]

If you wanted ohlins & they weren't available why opt for B14's & not B16's?

The oem suspension was crap over sprung & under dampen !

The B14s were a stop gap till Ohlins became available.

Dell.

[RS3Dell]

Just an update after taking the RS out on 3 occasions since fitting the Ohlins to find a day2day base setting for the damping including a 45min drive with James at the wheel down the country lanes near where he lives.

I started @ 10 clicks out off 20 were 1 is fully closed/hard 20 is fully open/soft.

I found on 10 i lost feed back from the chassis & couldn't feel for grip level but great turn in.

20 gave good feed back but made the suspension crashy & also lost the great turn in.

Now running on 15 which is a very good compromise between the the 2,this is backed up by James evaluation using those different settings tho he does prefer 10 for his driving style.

The Ohlins lineal rate springs are very much stiffer than the progressive wound B14 springs which shows up in the taut handling with suspension compliance over uneven/bumpy road surfaces.

Dell.

[jimojameso]

Thanks for the spin Dell. I was very impressed with the ohlins setup and is definitely something i will look at getting in the future. I second all of the above.

[MarkMac-RS3]

Think I might go for these on the 8V. Not a great deal more than KW’s had Ohlins on my motocross bikes and can’t fault them.

[RS3Dell]

Think I might go for these on the 8V. Not a great deal more than KW’s had Ohlins on my motocross bikes and can’t fault them.

Mark.

James said in his opinion the Ohlins felt better than the KWs V3s he had fitted to his TTRS.

Dell.

[StephenG]

https://www.audirs3o...s/?fromsearch=1

Some previous discussion here, link to audizine topic as well from Sean.

Edited by StephenG, 04 July 2020 - 08:01 AM.

[StephenG]

Not sure if issues are addressed, I'm looking for coilys for my FL also.