[Bronco]

Have an RS3 for sale nice and cheep. spot on to drive and very clean leather interior. Only done 25000 miles. Is on a cat d but is fully repaired, it only had a bit of a scuff on the rear panel. needs to go, Cheep enough for the misses or track tool at 21000 ono. PM if interested.

Attached Files

•  Picture 785.jpg   43.36K   47 downloads
•  Picture 787.jpg   44.32K   43 downloads

[Bronco]

Well we have finaly got on and started the engine on the new ecu. Needs a lot of sensor calibration and then mapping before it is allowed to run for a longer period but at least it runs. This has proved to be far more difficult than we thought. The wiring for the new PDU can now commence and the new CAN dash switches. PDU is 32 channel but will double up some none essential circuits. 

Attached Files

•  Picture 798.jpg   39.64K   35 downloads

Edited by Bronco, 26 October 2015 - 11:43 AM.

[nafonevs]

Any news on this? I seen it at Darren Lanes a few years ago. Whilst he was doing a cage for my brother

[Bronco]

Yes, the news is getting back on with it. The shell is now fully prepped and has been chemical dipped and zinc plated and is now finally at the paint shop. Will post up some photos of the bare painted shell and the subsequent build. should be 2 weeks max. Cheers Bronco./ Daz Lane.

[sawda]

This is gonna be something really special

Sent from my HTC 10 using Tapatalk

[nafonevs]

Amazing. Can't wait to see it

[Bronco]

 IMG_1294.JPG   59.78K   22 downloads  IMG_1295.JPG   56.37K   25 downloadsBeen getting some good progress with the build. Starting to see the end at last.

[dbm]

I haven't read the thread fully, so apologies if this has already been asked and answered: are you planning to compete with the car? What series would that be?

[Bronco]

It will compete in tarmac rallys. will be in same class as evos, suburus etc. Its not too far off being finished and will be rallied as soon as its done. its too early to commit to a full series but its being built to use.

Edited by Bronco, 18 April 2017 - 08:22 PM.

[dbm]

Nice!

[nafonevs]

IMG_1294.JPG IMG_1295.JPGBeen getting some good progress with the build. Starting to see the end at last.

Finally finished. Just seen it on group b in deeside getting mapped. What ecu did you run in the end? And have you got any under bonnet pics?

[Bronco]

Its not finished yet but is not too far off. It came off the rollers after a full day of mapping which threw up some problems with the standard intercooler. Very big and efficient one now on order. The engine and box are now back out ready to fit the new sequencial dog box which is nearly ready. will post up some photos when I find the blasted lead for the phone. The ecu is from Life Racing and is top notch. It contols the engine and the haldex. 

[rotarydynamics]

Bronco- Would you mind detailing the manual swap. I can guess but what are all the parts needed, and how does the stock ecu need to be tricked?

[Eigdoog]

What a beast! 

 

Would love to see this on the move!

[Bronco]

The swop to manual requires a TTRS  gearbox, TTRS dogbone lower mounting. TTRS gearstick and cables, TTRS gearbox mounting, TTRS nsf driveshaft.TTRS flywheel and clutch assembly. That makes it all work mechanically. We are not using stock ecu but would think a good mapper could get past any problem or fit TTRS ecu. If anyone is interested the full manual kit will be for sale soon. It is all brand new and has only been run on the rollers and a few blasts up the lane.